電動扭剪扳手主要用于鋼結構安裝行業，專門用于鋼結構高強螺栓的安裝。高強度螺栓用于連接鋼結構節點，通常采用螺栓組的形式。高強度螺栓可分為扭剪型和大六角型兩種。國標扭剪型高強度螺栓為M16、M20、M22、M24，非國標為M27、M30；國標大六角高強度螺栓為M16、M20、M22、M24、M27、M30等，一般高強度螺栓應先擰緊后擰緊，每一步都有嚴格的扭矩要求。所以，各種電動扭剪扳手都是為了滿足各種擰緊的需要。
Electric torsional shear wrench is mainly used in steel structure installation industry, especially for the installation of high-strength bolts of steel structure. High strength bolts are used to connect steel structure joints, usually in the form of bolt groups. High strength bolts can be divided into torsion shear type and large hexagon type. The national standard torsion shear high-strength bolts are M16, M20, M22 and M24, and the non-national standards are M27 and M30; National standard large hexagon high-strength bolts are M16, M20, M22, M24, M27, M30, etc. generally, high-strength bolts should be tightened first and then tightened, and there are strict torque requirements in each step. Therefore, all kinds of electric torsional shear wrenches are designed to meet the needs of various tightening.
電動扭剪扳手主要用于緊固扭剪高強度螺栓，其目的是折斷扭剪高強螺栓的梅花頭。工作時，將扳手頭對準螺栓頭，拉動開關開始工作。幾秒鐘后，螺栓的梅花頭就會折斷，然后拔出扳手扳動扳機將梅花頭彈出，這就是工作的結束。
The electric torsional shear wrench is mainly used to fasten the torsional shear high-strength bolt, and its purpose is to break the plum blossom head of the torsional shear high-strength bolt. When the wrench head is aligned with the bolt head, start to work. After a few seconds, the plum blossom head of the bolt will break, and then pull out the wrench and pull the trigger to eject the plum blossom head. This is the end of the work.
電動扭剪扳手主要用于鋼結構安裝行業，專門用于鋼結構高強螺栓的安裝。高強度螺栓用于連接鋼結構節點，通常采用螺栓組的形式。高強度螺栓可分為扭剪型和大六角型兩種。國標扭剪型高強度螺栓為M16、M20、M22、M24，非國標為M27、M30；國標大六角高強度螺栓為M16、M20、M22、M24、M27、M30等，一般高強度螺栓應先擰緊后擰緊，每一步都有嚴格的扭矩要求。所以，各種電動扭剪扳手都是為了滿足各種擰緊的需要。
Electric torsional shear wrench is mainly used in steel structure installation industry, especially for the installation of high-strength bolts of steel structure. High strength bolts are used to connect steel structure joints, usually in the form of bolt groups. High strength bolts can be divided into torsion shear type and large hexagon type. The national standard torsion shear high-strength bolts are M16, M20, M22 and M24, and the non-national standards are M27 and M30; National standard large hexagon high-strength bolts are M16, M20, M22, M24, M27, M30, etc. generally, high-strength bolts should be tightened first and then tightened, and there are strict torque requirements in each step. Therefore, all kinds of electric torsional shear wrenches are designed to meet the needs of various tightening.
電動扭剪扳手是擰緊螺栓的工具，它可以幫助您安裝和拆卸螺栓和螺母，并更準確地控制擰緊力矩。當扳手達到一定扭矩時，螺栓的梅花頭即可被切斷。螺栓的V形切口保證了扭矩精度和軸向拉力，拆裝扭矩大，比手動操作更安全可靠。
Electric torsion shear wrench is a tool for tightening bolts. It can help you install and remove bolts and nuts, and control the tightening torque more accurately. When the wrench reaches a certain torque, the Torx head of the bolt can be cut off. The V-shaped notch of the bolt ensures the torque accuracy and axial tension. The disassembly torque is large, which is safer and more reliable than manual operation.
