可曲撓橡膠軟接頭安裝說明英語版
可曲撓橡膠軟接頭安裝說明英語版
一、可曲撓橡膠軟接頭特點：
一、flexible rubber joint characteristics:
1、可曲撓橡膠軟接頭可降低管道系統的震動和噪聲，可解決各類管路的接口位移，軸向伸縮及不同心、度等問題。
1, flexible rubber joint capable of reducing vibration and noise of the pipeline system, which can solve the interfacedisplacement of pipeline, axial expansion and notconcentric, degree of.
2、根據材料不同可曲撓橡膠軟接頭可制成耐酸、耐堿、耐腐蝕、耐油、耐熱等各類品種，適應多種介質和環境。
2, according to the different materials of flexible rubber joint can be made of acid and alkali resistance, corrosion resistance, oil resistance, heat resistance and other varieties, to adapt to a variety of media and the environment.
3、可曲撓橡膠軟接頭材料屬極性橡膠，密封性好，重量輕，安裝維修方便、使用壽命長，但必須避免與鋒利金屬器械等接觸，以免刺破球體，影響質量。
3, flexible rubber joint material is a polar rubber, good sealing performance, light weight, convenient installation and repair, long service life, but must avoid sharp metalequipment contact, lest punctured sphere, affecting the quality of.
4、如可曲撓橡膠軟接頭架空使用須配彈性支架，安裝時螺栓要用對角法上緊。
4, such as flexible rubber joint overhead using to be equipped with elastic support, the installation bolts to betightened with diagonal method.
5、如可曲撓橡膠軟接頭管路壓力過高時，應用極限螺栓將兩端法蘭連在一起。
5, such as flexible rubber joint pipe pressure is too high,the application limit bolt flange connected together at both ends.
6、可曲撓橡膠軟接頭壓力的選擇：要根據泵的揚程來選擇，一般常用接頭的工作壓力有0.6、1.0、1.6、2.5Mpa。
6, flexible rubber joint pressure choice: according to the pump head to select, common joint work pressure of 0.6,1, 1.6, 2.5Mpa.
7、可曲撓橡膠軟接頭的使用溫度：要根據所輸送的介質來選擇，一般在-15℃～80℃特殊可達-30℃～140℃。
7, use temperature of flexible rubber joint: according tothe transmission medium to select, generally in the -15 ℃ ~ 80 ℃ to -30 ℃ ~ 140 ℃ special.
8、可曲撓橡膠軟接頭的使用介質：一般接頭適用介質為：空氣、壓縮空氣、水、海水、熱水、油、酸、堿等。
8, use the medium of flexible rubber joint: a general jointfor medium: air, compressed air, water, sea water, hot water, oil, acid, alkali etc..
9、特殊環境下須考慮爆破壓力和真空度等。
9, the special environment should consider blastingpressure and vacuum degree.
10、當管道介質為酸堿、油、高溫及其他特殊材料時應選用高于管道工作壓力一個檔位的接頭。
10, when the medium in the pipeline for pH, oil, high temperature and other special materials should be higher than the working pressure of pipeline joints on a gear.Making
選用對的對等法蘭盤是為了要給予*，耐久以及安全的連接方法;
The equivalence of the flange is to give perfect, durableａnd safe connection method;
選擇管道平焊法蘭請采用以下的標準（對夾式蝶閥專用法蘭）
Select a pipeline flange please use the following standard(wafer type butterfly valve special flange)
a) 水管道口其連接部位的內徑一定要與橡膠防震接頭的內徑一樣。
A) pipe crossing the junction diameter must with a shockproof rubber joint diameter.
b) 連接在水管道口的法蘭其法蘭接觸面一定要光滑及平整為了確保能有的密封空間。 (如下圖所示), 橡膠防震接頭沒有與水管道口接觸面有緊密接合時，就會有噪音產生, 壓力不足以及且會有漏水等現象發生。
B) flange connected to a water pipe crossing the flange contact surface must be smooth and flat to ensure it hadsealed the biggest space. (as shown below), a shockproof rubber joint had no contact with water crossing are closely connected, there will be noise, low pressure and would have Water Leakage phenomenon.
安裝橡膠防震接頭注意
Install rubber shockproof joint attention
正確安裝橡膠防震接頭在水管道上，應該采用下圖設汁標準以防上橡膠防震接頭會有過度伸長的現象發生。
The correct installation of rubber shockproof joint on the water line, the design standards should be adopted to prevent the occurrence of rubber anti vibration joint haveexcessive elongation phenomenon.
2.橡膠防震接頭是當固定支架安裝好在水管道時馬上安裝上去，安裝好后在橡膠防震接頭后面的水管道一定要裝有管道引導支架去支撐水管道。
2 rubber shockproof joint is best when the fixed bracket is installed in pipe immediately installed, water pipesinstalled behind the rubber shockproof joint must be equipped with pipeline guide bracket to support water pipeline.
鎖法蘭螺絲時請使用對的扭力
Lock the flange screws use of torsion
為了要讓橡膠防震接頭可以伸展到它的移位以及為了要保護產品的表面，安裝螺絲時，請從橡膠防震接頭所連接法蘭的法蘭口處放進螺絲。
In order to make rubber shockproof joint can be stretched to its maximumdisplacement and for surface protection products, screw installation, pleaseflange from a shockproof rubber joint flange at the mouth into the screw.
螺紋及螺母表面不能有利口。
Screw and nut surface can not have.
為了要讓產品與水管道口緊密的接觸，鎖螺絲時應采用對角方式。
In order to keep the products and water crossing close contact, locking screwsshould be used when the diagonal method.
其參考以下扭力數據
Following the reference torque data
產品尺寸小于3"(80mm) 60Nm.()
The product size is less than 3 "(80mm) 60Nm. (max)
產品尺寸大于4"(100mm) 80Nm.()
Product size greater than 4 "(100mm) 80Nm. (max)
二、可曲撓橡膠軟接頭安裝使用說明
二、flexible rubber joint installation instructions
1、橡膠軟接頭在安裝時嚴禁超位移極限安裝。
1, rubber joint in the installation of non super displacement limit installation.
2、平地、懸空、垂直安裝橡膠軟接頭時，橡膠軟接頭的實際工作軸向位移壓力應小于管道的支撐力，以防止工作時受壓拉脫。
2, flat, hanging, vertical installation of rubber joints, the actual work axial displacement pressure of rubber joints should be smaller than the pipe supportforce, to prevent the work pressure off.
3、管道必須有固定支撐或固定托架，固定托架的力必須大于軸向力。垂直安裝和架空安裝時橡膠軟接頭兩端需安裝相應的固定支架和受力支架，以防止工作受壓后拉脫。
3, the pipeline must be fixed or fixed support bracket, a fixed bracket force must be greater than the axial force. Vertical installation and overhead installation ofrubber joints at both ends need to install the corresponding fixed bracket and force support, in order to prevent the work pressure after pulling out.
4、安裝螺栓要對稱逐步加壓擰緊，以防局部泄露。
4, install bolts to be symmetric pressurize gradually tightened, to prevent localleakage.
5、1.0MPa以上的工作壓力，安裝螺栓要有彈性壓墊，以防工作時螺栓松動。
5, 1.0MPa above the work pressure, mounting bolts to elastic pad, to prevent thework of bolt looseness.
6、橡膠軟接頭在運輸裝卸時嚴禁銳利器具劃破表面、密封面。
6, rubber joints in transportation and handling of non sharp instruments across the surface, the sealing surface.
注意事項：
Matters needing attention:
1、可曲撓橡膠軟接頭管道施工時，必須讓其處于自然狀態，不要在安裝時使產品產生人為變形。
1, flexible rubber joint of pipeline construction, which must be in a natural state,not in the installation produces artificial deformation.
2、當管道介質為酸、堿、油、高溫及其他特殊材料時應選用高于管道工作壓力一個檔位的接頭。
2, when the medium of the pipeline is the acid, alkali, oil, high temperature and other special materials should be higher than the working pressure of pipelinejoints on a gear.
3、連接橡膠軟接頭的法蘭應是閥門法蘭或符合 GB/T9115.1(RF)的法蘭。
Flange 3, connect the rubber joint should be the valve flange or with GB/T9115.1(RF) flange.
4、橡膠軟接頭正常適用介質是溫度0-60°C的普通水，特殊介質如：油、酸堿、高溫及其他腐蝕性和質地堅硬的情況下，應選用相對應得特耐材料橡膠軟接頭，不可盲目串用或通用。
4, rubber joint normal suitable medium is ordinary water temperature 0-60 ° C,special media such as: oil, acid, high temperature and other corrosive and hardcase, should use relative deserve special refractory material of rubber joints, not blindly string or general.
5、橡膠軟接頭使用在水泵進出口時，應位于水泵一側，與水泵之間應安裝金屬變徑接頭，且安裝在變徑的大口徑處。
5, rubber joints used in the outlet of the pump, should be located in the pump side, the installation of metal reducing joint and water pump, and is installed in the large diameter at variable.
6、當管道位移量大于等于接頭的補償量時，應增加接頭的數量來平行位移量，嚴禁為了調整管道的超差，使接頭處于極限的撓曲位移和偏差狀態，更不能超限度（伸縮、位移、偏轉等）高層給水或懸空給水，管道應固定在吊架、托架或錨架上，且不能讓接頭承受管道自身重量和軸向力。
6, when the maximum amount of compensation pipeline displacement is greater than or equal to the number of joints, should increase the joint to paralleldisplacement, is strictly prohibited in order to adjust the pipeline ultra poor, so that the joint is in the limit of the flexural displacement and deviation state, but notexcessive (expansion, displacement, deflection) high layer water or suspendedwater supply, pipeline should be fixed in the bracket, bracket or anchor frame,ａnd not allow joint weight and axial force of pipeline.
7、安裝橡膠軟接頭時，螺栓的螺桿應伸向接頭外側，每一法蘭端面的螺栓按對角加壓的方法反復均勻擰緊，防止壓偏。絲扣接頭應使用標準扳手勻力擰緊，不要用加力稈加力使活接頭滑絲、滑棱和斷裂，而且要定期檢查，以免松動造成脫盤或滲水。
7, installation of rubber joints, bolt should be toward the joint outer, tighten thebolt flange end face of each diagonal compression of repeated uniform, to prevent the pressure deviation. Threaded joint should use the standard uniform force wrench tightening, don't use the afterburner afterburner make joint stalkslide wire, gliding and fracture, and regularly check, so as not to loose off thedisk or seepage.
8、橡膠軟接頭在初次承受壓力（如：安裝試壓等）后或長期停用再次啟用前，應將螺栓重新加壓擰緊再投入運行。
8, rubber joints under pressure in the first (such as: installation and pressure testetc.) or long-term disabled enabled again, should be re tightened bolt pressureagain put into operation.
9、使用或儲存橡膠軟接頭，應避免高溫、臭氧油及酸堿環境。用在室外或向陽迎風的管道應搭建遮陽架，嚴禁暴嗮、雨淋、風濁。接頭表面嚴禁刷漆和纏繞保溫材料。因橡膠制品存在老化問題，應及時檢查更換。
9, use or storage of rubber joints, should avoid high temperature, oil and acidenvironment of ozone. The pipeline outside or Xiangyang upwind should construct the sunshade frame, no violence 嗮, Yu Lin, wind erosion. A joint surface is strictly prohibited to brush paint and winding insulation materials.Because the rubber product aging issues, should be timely replacement.
注：以上可曲撓橡膠軟接頭安裝使用說明，請嚴格規范使用，如不當使用造成任何后果，概不負責。
Note: the above flexible rubber joint installation instructions, please strictlyregulate the use, such as caused by the improper use will not be responsible forany consequences.
版權與免責聲明：
1.凡本網注明"來源：全球制造網"的所有作品，版權均屬于全球制造網，轉載請必須注明全球制造網。違反者本網將追究相關法律責任。
2.企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
3.本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
4.如涉及作品內容、版權等問題，請?jiān)谧髌钒l(fā)表之日起一周內與本網聯系。
網站客服
